• OMAX 2652 Front
    † Photo may show optional accessories
  • OMAX 2652 Left
    † Photo may show optional accessories
  • OMAX 2652 Top
    † Photo may show optional accessories
  • OMAX 2652 Right
    † Photo may show optional accessories

The OMAX 2652 JetMachining Center is slightly larger than the OMAX 2626, but still offers a small footprint for space-challenged shops. The OMAX 2652 is a mid-sized cantilever-style machine. With a completely sealed and protected ball screw drive system, this robust and reliable workhorse is perfect for shops cutting projects with smaller dimensions but needing high precision.

Units:
  • OMAX 2652 Front View

    7’ 11” Height 2,413 mm Height
    OMAX 2652 Front
    11’ 7” Length 3,531 mm Length
  • OMAX 2652 Side View

    7’ 11” Height 2,413 mm Height
    OMAX 2652 Side
    5’ 7” Width 1,702 mm Width

Machine Dimensions

Footprint * – (L x W) 11’ 7” x 5’ 7” 3,531 mm x 1,702 mm
Height ** 7’ 11” 2,413 mm
Weight (tank empty) 3,320 lb 1,506 kg

Work Envelope

X-Y Cutting Envelope *** 4’ 4” x 2’ 2” 1,321 mm x 660 mm
Z-Axis Travel *** 8” 203 mm
Table Size – (L x W) 5’ 9” x 2’ 6” 1,753 mm x 762 mm

Standard Model Specifications

Speed 180 in/min 4,572 mm/min
Linear Positional Accuracy ±0.0010" ±0.0254 mm
Repeatability ±0.0010" ±0.0254 mm
Ballbar Circularity ±0.0025" ±0.0635 mm

All products meet rigorous international standards and requirements. Learn more »

* Footprint includes controller but not the pump.

** With standard scissor plumbing.

*** Additional accessories may reduce travel.

  • Fastest cutting speeds and best precision compared to any competitive abrasive waterjet in the industry
  • Backed by our exclusive IntelliMAX Software with real world cutting data
  • Robust and accurate design for tight tolerance cutting and reliable operation
  • Easy operator access to the work area
  • Small, efficient footprint for minimal floor space utilization
  • Precision X-Y Axis rigidly mounted to the cutting table
  • Pre-loaded linear bearings and precision ball screws
  • Drive system sealed against water, dirt, and grit
  • No tool changes & minimal fixturing dramatically reduce setup
  • Machines a wide range of materials and thicknesses, from metals and composites to glass and plastics
  • Leaves behind a satin-smooth edge, reducing secondary operations
  • Does not create heat-affected zones or mechanical stresses
  • Environmentally "green" system uses only natural garnet abrasive and water in the cutting process
  • No noxious fumes, liquid or oils used in, or caused by, the machining process
  • Shipped as a completely pre-assembled and factory-tested system
  • Designed and manufactured at the OMAX factory in Kent, Washington, USA
  • Standard programmable Motorized Z-Axis with a precision OMAX MAXJET 5i Nozzle boosts productivity and process efficiency
  • Standard IntelliCAM software program is available with two tools in one that can generate either 2D or 3D tool paths from 3D models.
  • Standard IntelliVISOR SE System Monitoring offers predictive maintenance and system monitoring to minimize unexpected downtime
  • Standard scissor-style hard plumbing adds another level of safety by using contained high-pressure components, as well as contributes to a smaller footprint, lower maintenance, and higher reliability
  • Standard Rapid Water Level Control for cleaner, safer, and quieter submerged cutting completes most work below 80 dBA
  • Optional Bulk Abrasive Delivery System transports garnet from the assembly's large hopper into the Zero Downtime Hopper located on the Z-Axis
  • Optional Tilt-A-Jet taper eliminating abrasivejet cutting head
  • Optional Variable Speed Solids Removal System (VS-SRS) designed for industrial use increases uptime through automated solids removal
  • High efficiency EnduroMAX pump system available in 30 hp, 40 hp, 50 hp or 100 hp with operating efficiencies up to 85%
  • EnduroMAX pump technology delivers the highest nozzle horsepower in the industry for faster and more efficient cutting
  • Highly robust and reliable pump design capable of over 1,000 hours between maintenance
  • Uses substantially less cooling water than inefficient hydraulic intensifier pumps
  • Lowest electrical consumption compared to other pump technology
 

What Owners Say

  • We realized how much money we saved if we kept most of our cutting work in-house instead of outsourcing.

    Mr. Makis of Custom Precision Technologies
  • The waterjet's cold cutting process is cleaner; we don't have to worry about modifying the chemistry of our specimens or intro­ducing heat.

    Brandon McVaugh of Laboratory Testing Inc.
  • The technicians have been available, courteous, well trained and very helpful.

    Dan Claxton of Composiflex
  • The dining table was a very exciting project which could not have been done without the OMAX.

    Peter of Carapace Armor Technology
  • The OMAX machine made it possible for us to survive during this very difficult economic period.

    Torres of Amaida Machine Shop, LLC
What can we help you with?