Machine Photo
Overview
Features / Benefits
Specifications

{content}

Overview

Large scale precision machining: For larger parts or multiple parts from large stock up to 6' x 12' This model 80160 JetMachining Center cuts complex flat parts out of most materials including metal, plastic, glass, ceramics, stone and composites directly from a CAD drawing or .DXF file. Extremely hard, reflective and nonconductive materials can also be cut, making it a valuable addition to existing shop capabilities. No tool changes or complex fixturing dramatically reduces setup times and the smooth finish often eliminates the need for secondary machining.

Features / Benefits

Standard Features

• OMAX intelli-MAX® software offers higher average cutting speeds and greater precision with free upgrades for the life of the machine
• Programmable Motorized Z-axis with precision OMAX MAXJET® 5 Nozzle Assembly
• Ball screw drive inside the Y-axis bridge fully enclosed inside bellows
• Ball screw drive inside X-axis fully enclosed inside coated steel covers
• Scissor-style hard plumbing
• Component protection against water, dirt, and grit
• High efficiency direct drive pump systems available in 30, 40, 60, 70 and 80 hp with pressures up to 55,000 psi
• Rapid water level control for submerged cutting.
• Bulk Abrasive Feed Assembly transports garnet from the assembly's large hopper into the small hopper located at the Z-axis
• Solids Removal System (SRS) designed for tough industrial use (available as an option)
• Tilit-a-Jet® taper compensating abrasivejet cutting head (available as an option)
• Shipped as a completely pre-assembled and factory tested system.

Abrasivejet Benefits

• Machines a wide range of materials and thicknesses
• Does not create heat affected zones or mechanical stresses
• Rapid setup, no tool changes required
• Minimal fixturing required
• Leaves behind a satin smooth edge, reducing secondary operations
• No noxious gases, liquids or oils used in (or caused by) the machining process
• Completes most work below 80 dBA at 1 meter for submerged cutting
• Environmentally "green" system with quiet and clean operation, low electrical and abrasive consumption

Specifications

Machine Dimensions

Footprint 243" x 134" (6170 mm x 3405 mm)
Footprint with optional SRS 288" x 134" (7315 mm x 3405 mm)
Weight (tank empty) 10,000 lbs (4500 kg)
Height 144" (3660 mm)
Operating Weight 35,000 lbs (15,900 kg)

Work Envelope

X-Y Travel 168" x 80" (4267 mm x 2030 mm )
Table Size 174" x 89" (4419 mm x 2261 mm)
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported Material Load 250 lbs/sq. ft. (1,200 kg/sq. meter)
(Optional accessories may reduce travel. Contact OMAX for information.)

Computer Control System

Hardware: Personal computer
Control Software: Integrated CAD/CAM system directly uses .DXF files

Drive Description

Closed loop, digital drives
Brushless servo motors
Pre-loaded ball screws with recirculating ball bearings and hardened precision ground ways in Y-axis bridge
Ball screw drive in X-axis
Motor controlled precision Z-Axis

Accuracy of Motion at 70° F

Ballbar Circularity (Over 12")
At Max. Traverse Velocity ±0.003" (±0.08 mm)
Repeatability ±0.002" (±0.051 mm)
Squareness 0.002" per foot (0.17 mm/m)
Straightness 0.003" per foot (0.25 mm/m)
Backlash 0.0007" maximum (0.018 mm)

Speed

180 inches per minute standard (4572 mm/min)

Electrical Requirements

3-Phase, 380-480 VAC ±10%, 50-60 Hz
(Note: Contact OMAX for detailed utility requirements. Pumps are built to meet UL and CE specifi cations.)

Pump Options

30 horsepower, 50,000 psi (3500 bar)
40 horsepower, 55,000 psi (3850 bar)
Dual Pump Package (redundant 30 hp or 40 hp)

Noise Level

Below 80 dBA at 1 meter for submerged cutting

Note: Specifications subject to change without notice.

Materials Cut

Materials Cut

Each OMAX JetMachining Center is designed to easily cut an array of materials and thicknesses, from stone, metal, plastic and glass, to rubber, ceramics and composites. Currently, the most profitable precision applications involve metals such as aluminum, tool steel, stainless steel, mild steel and titanium, all materials commonly used in many engineering applications. With the ability to quickly and accurately machine nearly any two-dimensional shape imaginable in thickness up to 1" (2.5cm) or less than 1" (25 mm), OMAX is a versatile addition to any machine shop.

To learn more about OMAX machining capabilities for different materials click on any icon below:

Financing

OMAX® Corporation and your OMAX distributor work with virtually all national lenders, each of whom consider the OMAX JetMachining® Center an excellent in fact "preferred" -- collateral.  That preferential treatment means we can tailor financing to your particular requirements.  Some of our program features include:

• Ease of Approval (many to most approvals on a one page credit application for an existing business)
• Delayed Payments
• Low Down Payments
• "Start-Up" Financing
• Financing Options for Upgrades to Your OMAX JetMachining Center (because every OMAX Center upgradeable for new options, since the first OMAX Center)
• Most importantly extended terms leases to 84 months, often with no prepayment penalties*

If you need particular lease features JUST ASK. At OMAX, we often work with our "lender network" to create a customized lease structure for you.

* subject to a minimum twelve payments having been received.