Machine Photo
Overview
Features / Benefits
Specifications

{content}

Overview

Precision machining workhorse: From prototypes to production runs in sizes up to 4' x 8'. The Model 55100 JetMachining Center cuts complex flat parts out of materials including metal, plastic, glass, ceramic and composites directly from a CAD drawing or .DXF file. JetMachining is ideal for short-run part production, just-in-time manufacturing, tooling and prototype part development. No tool changes or complex fixturing reduces setup times by at least 50%

Features / Benefits

Standard Features

• OMAX Intelli-MAX® software offers higher average cutting speeds and greater precision with free upgrades
• Programmable Motorized Z-Axis with precision OMAX MAXJET® 5 Nozzle Assembly
• Precision X-Y axis rigidly mounted to the cutting table
• Pre-loaded linear bearings and precision ball screws.
• Scissor-style hard plumbing
• Component protection against water, dirt, and grit.
• High efficiency direct drive pump system available in 30, 40, 60, 70, and 80 hp with pressures up to 55,000 psi
• Rapid water level control for quiet and clean submerged cutting.
• Bulk Abrasive Delivery System transports garnet from the assembly's large hopper into the small hopper located at the Z-axis
• Solids Removal System (SRS) designed for tough industrial use (available as an option)
• Tilt-A-Jet® taper compensating abrasivejet cutting head (available as an option)
• Shipped as a completely pre-assembled and factorty tested system

Abrasivejet Benefits

• Machines a wide range of materials and thicknesses.
• Does not create heat affected zones or mechanical stresses.
• Rapid set-up, no tool changes are required.
• Minimal fixturing required.
• Leaves behind a satin smooth edge, reducing secondary operations.
• No noxious gases, liquids, or oils are used in (or caused by) the machining process.
• Completes most work below 80 dBA at one meter for submerged cutting
• Environmentally "green" system with quiet and clean operation, low electrical and abrasive consumption
  

Specifications

Machine Dimensions

Footprint 155" x 94" (3937 mm x 2388 mm)
Weight 8000 lb (3629 kg)
Height 118" (2998 mm)
Operating Weight 22,000 lb (10,000 kg) (with water in tank)

Work Envelope

X-Y Travel 100" x 55" (2540 mm x 1397 mm)
Table Size 126" x 65" (3200 mm x 1650 mm)
Material Supported Slats 4" x 1/8" Galvanized Steel
(Optional accessories may reduce travel. Contact OMAX for information.)

Computer Control System

Hardware: Personal computer
Control Software: Integrated CAD/CAM system directly uses .DXF fi les

Drive Description

• Closed loop, digital drives
• Brushless servo motors
• Pre-loaded ball screws, recirculating balls
• Linear bearings with hardened, precision ground ways
• Cantilever Y-Axis on bridge X-Axis

Accuracy of Motion at 70° F

Ball Bar Circularity (Over 12")
At Max. Traverse Velocity ±0.003" (±0.08 mm)
Repeatability ±0.002" (±0.051 mm)
Squareness 0.002" per ft (0.17 mm/m)
Straightness 0.003" per ft (0.25 mm/m)
Backlash 0.0007" max. (0.018 mm)

Speed

180 inches per minute standard (4572 mm/min)

Electrical Requirements

3-Phase, 380-480 VAC ±10%, 50-60 Hz
(Note: Contact OMAX for detailed utility requirements. Pumps are built to meet UL and CE specifications.)

Pump Options

30 horsepower optional; 50,000 psi
40 horsepower optional; 55,000 psi
Dual Pump Package (redundant 30 hp or 40 hp)

Noise Level

Below 80 dBA for submerged cutting

Note: Specifications subject to change without notice.

Materials Cut

Materials Cut

Each OMAX JetMachining Center is designed to easily cut an array of materials and thicknesses, from stone, metal, plastic and glass, to rubber, ceramics and composites. Currently, the most profitable precision applications involve metals such as aluminum, tool steel, stainless steel, mild steel and titanium, all materials commonly used in many engineering applications. With the ability to quickly and accurately machine nearly any two-dimensional shape imaginable in thickness up to 1" (2.5cm) or less than 1" (25 mm), OMAX is a versatile addition to any machine shop.

To learn more about OMAX machining capabilities for different materials click on any icon below:

Financing

OMAX® Corporation and your OMAX distributor work with virtually all national lenders, each of whom consider the OMAX JetMachining® Center an excellent in fact "preferred" -- collateral.  That preferential treatment means we can tailor financing to your particular requirements.  Some of our program features include:

• Ease of Approval (many to most approvals on a one page credit application for an existing business)
• Delayed Payments
• Low Down Payments
• "Start-Up" Financing
• Financing Options for Upgrades to Your OMAX JetMachining Center (because every OMAX Center upgradeable for new options, since the first OMAX Center)
• Most importantly extended terms leases to 84 months, often with no prepayment penalties*

If you need particular lease features JUST ASK. At OMAX, we often work with our "lender network" to create a customized lease structure for you.

* subject to a minimum twelve payments having been received.