Machine Photo
Overview
Features / Benefits
Specifications

{content}

Overview

OMAX 120X JetMachining Center

Designed for large scale precision machining of larger parts or multiple parts from stock up to 10' x 20' (3 m x 6 m).The Model 120X JetMachining Center cuts complex flat parts out of most materials including metal, plastic, glass, ceramics, stone and composites directly from a CAD drawing or .DXF file. It can also cut extremely hard, reflective and non-conductive materials, making it a valuable addition to existing shop capabilities. No tool changes or complex fixturing reduces setup times and the smooth finish often eliminates the need for secondary machining.

OMAX 120X/S JetMachining Center

The 120X/S has an X-Y cutting travel of 10' x 13' (3 m x 4 m)

OMAX 120X-1 JetMachining Center

The 120X-1 has an X-Y cutting travel of 10' x 26' (3 m x 8 m)

OMAX 120X-2 JetMachining Center

The 120X-2 has an X-Y cutting travel of 10' x 32' (3 m x 10 m)

 

 

 

Features / Benefits

Standard Features

• OMAX Intelli-MAX® software offers higher average cutting speeds and greater precision with free upgrades for the life of the machine
• Programmable Motorized Z-axis with precision OMAX MAXJET® 5 Nozzle Assembly
• Intelli-TRAX™ traction drive on both the X and Y-axis
  
• Scissor-style hard plumbing
• Component protection against water, dirt, and grit
• High efficiency direct drive pump systems available in 30, 40, 60, 70 and 80 hp with pressures up to 55,000 psi
• Rapid Water Level Control for quiet and clean submerged cutting
• Bulk Abrasive Feed Assembly transports garnet from the assembly's large hopper into the small hopper located at the Z-axis
• Solids Removal System (SRS) designed for tough industrial use (available as an option)
• Tilt-A-Jet® taper compensating abrasivejet cutting head (available as an option)
• Shipped as a completely pre-assembled and factory-tested system
  

Abrasivejet Benefits

• Machines a wide range of materials and thicknesses
• Does not create heat-affected zones or mechanical stresses
• Rapid setup, no tool changes required
• Minimal fixturing required
• Leaves behind a satin smooth edge, reducing secondary operations
• No noxious gasses, liquids or oils used in (or caused by) the machining process.
• Completes most work below 80 dBA at 1 meter for submerged cutting.
• Environmentally "green" system with quiet and clean operation, low electrical and abrasive consumption
  

Specifications

Machine Dimensions

Footprint 340" x 207" (8636 mm x 5258 mm)
Weight (tank empty) 15,000 lbs (6803 kg)
Height 168" (4267 mm)
Operating Weight 61,000 lbs (27669 kg)

Work Envelope

X-Y Travel 240" x 120" (6096 mm x 3048 mm)
Table Size 259" x 137" (6579 mm x 3480 mm)
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported Material Load 250 lbs/sq. ft. (1,200 kg/sq. meter)

Computer Control System

Hardware: Personal computer
Control Software: Integrated CAD/CAM system directly uses .DXF files

Drive Description

Closed loop high pole vector drives
Stainless steel hardened precision ground shaft ways
Intelli-TRAX Drive with linear encoder in both X and Y-axis
Motor controlled precision Z-axis

Accuracy of Motion at 70° F

Ballbar Circularity (Over 12")
 ±0.005"

Speed

350 inches per minute standard (8890 mm/min)

Electrical Requirements

3-Phase, 380-480 VAC ±10%, 50-60 Hz
(Note: Contact OMAX for detailed utility requirements. Pumps are built to meet UL and CE specifications.)

Pump Options

30 horsepower, 55,000 psi (3850 bar)
40 horsepower, 55,000 psi (3850 bar)
Dual Pump Package (redundant 30 hp or 40 hp)

Noise Level

Below 80 dBA at 1 meter for submerged cutting

Note: Specifications subject to change without notice.